Fluke ESA612 115V ac Electrical Safety Analyzer Medical Equipment Tester ESA-612
The Following Items Are Included. Fluke ESA612 115 VAC Electrical Safety Analyzer (BC# 34235-L/T). (2) 1000V Hard Point Test Leads.
Fluke ESA612 115V ac Electrical Safety Analyzer The ESA612 offers the functionality of a simulator, multimeter and electrical-safety analyzer in a single test tool With selection of two test loads, this versatile product can be used worldwide to test to preventative maintenance electrical safety standards of choice: ANSI/AAMI ES1:1993 (NFPA-99), IEC62353 (VDE 751), and AN/NZS 3551 Includes Carrying Case & Acccessories As Listed Above! Fluke Networks ESA612 Electrical Safety Analyzer. The ESA612 Electrical Safety Analyzer represents the next generation in testers for biomedical professionals that perform field service on medical equipment throughout their facilities, in clinics, and anywhere onsite service is required.Portable, lightweight, and designed for operation in tight spaces, the ESA612 offers the functionality of a simulator, multimeter and electrical-safety analyzer in a single test tool. With selection of two test loads, this versatile product can be used worldwide to test to preventative maintenance electrical safety standards of choice: ANSI/AAMI ES1:1993 (NFPA-99), IEC62353 (VDE 751), and AN/NZS 3551.
The versatility of the multifaceted ESA612 is further expanded with optional automation software, which speeds and simplifies testing and provides high-end-analyzer productivity at software-level investment. Ansur-automated ESA612 standardizes test procedures, compares results to standards limits, and generates and stores reports for total digital data management. Portable, ergonomic, lightweight and easy to use.
Large, easy-to-read display with adjustable contrast. Bail design for stand-up testing in field environments. Five applied parts jacks and easy ECG snap connection with optional expander box. ECG waveform tests and dual-lead measurements combine the functionality of a simulator, multimeter and electrical-safety analyzer in a single test tool. Replaceable mains fuses keep the device in the field and out of the repair shop. Internal memory for 100 test records. 20 A at 120 V current capability. USB connection for use with Ansur and Data Viewer software (for memory download to PC).Optional Ansur automation software standardizes test procedures, compares results to standards limits, generates/stores reports and provides total digital data management. Rigorously tested for rugged field applications, with CE and CSA in addition to the Fluke-quality-design stamp of approval.
90 V ac to 132 V ac rms. 0 V ac to 300 V ac rms.
± (2 % of reading + 0.2 V). 0 W to 2 W. ± (2 % of reading + 0.015 W). 0 A to 20 A. ± 5 % of reading + (2 counts or 0.2 A, whichever is greater).
15 A to 20 A, 5 min on/5 min off 10 A to 15 A, 7 min on/3 min off 0 A to 10 A continuous. Modes Modes are available in all leakage tests with the exception of MAP leakages that are available only in true-rms. AC + DC (true-rms) AC only DC only. Patient load selection (input impedance).A 2 mA to 10 mA. Frequency response/accuracy DC to 1 kHz 1 kHz to 100 kHz 100 kHz to 1 MHz.
± 1 % of reading + (1? A or 1 LSD, whichever is greater) ± 2 % of reading + (1? A or 1 LSD, whichever is greater) ± 5 % of reading + (1? A or 1 LSD, whichever is greater). Ground wire (earth) Chassis (enclosure) Lead to ground (patient) Lead to lead (patient auxiliary) Lead isolation (mains on applied part) Direct equipment Direct applied part Alternative equipment Alternative applied part Point to point. Mains on applied part test voltage. A 2 mA to 20 mA. ± 10 % of reading + (2 counts or 20? 0.5 MW to 20 MW 20 MW to 100 MW.± (2 % of reading + 0.2 MW) ± (7.5 % of reading + 0.2 MW). 500 V dc 250 V dc.
Mains-PE, AP-PE, Mains- PE, Mains-NE (non-earthed accessible conductive part) and AP- NE (non-earthed accessible conductive part). ± 2 % ± 5 % for amplitude of 2 Hz square wave only, fixed at 1 mV Lead II configuration. Square wave (50 % duty cycle) (Hz) Sine wave (Hz) Triangle wave (Hz) Pulse (63 ms pulse width). 30, 60, 120, 180, and 240 0.125 and 2 10, 40, 50, 60, and 100 2 30 BPM and 60 BPM. Mains voltage inlet power range. 90 to 132 V ac rms. 10 °C to 40 °C (50 °F to 104 °F). 20 °C to 60 °C (-4 °F to 140 °F). 10 % to 90 % non-condensing. 120 V ac mains supply voltage up to 5,000 m. Please check our Huge Inventory with savings of up to 80% off of retail on Cat5/5e/6 LAN Cable Certifiers and Fiber Optic OTDR's, Fusion Splicers, CATV Meters, Fiber Optic Kits, Sources, Meters, Tools, Network Analyzers and much more. Here is a Link to our. Please don't hesitate to. For a Quote on Something you don't see in our inventory, sometimes we have items that may have not been listed or processed yet. Test Equipment Store Offers a wide range of Refurbished Telecom/ Datacom Tools and Test Measurement Equipment. Which includes Fiber Optic Test and Splicing tools, Fusion Splicers, OTDRs, Copper and Fiber Cable Certifiers, CATV Test Equipment, Cable and Antenna Analyzers, Network Analyzers and much more!We carry a large inventory of quality refurbished and used test equipment from all the major manufacturers. If you are looking for multiple quantities or if we don't have a listing for a particular item that you are looking for. (Certain orders may take longer for processing due to comprehensive final service inspections).